Grindmaster P200E User Manual download pdf

P200E Shuttle & RAPS200E

Airpot/Shuttle Brewer Series

Operation and Instruction Manual

Installation

WARNING: ELECTRIC SHOCK HAZARD!

INSTALLATION OF THIS APPLIANCE SHOULD BE PERFORMED BY

QUALIFIED SERVICE PERSONNEL ONLY. IMPROPER

INSTALLATION COULD RESULT IN ELECTROCUTION.

See rough-in drawings in this manual for dimensions and locations of

electric and water input.

Set-Up/Position

1) Remove the brewer from the packing material and attach its legs.

2) Position the brewer on a strong, stable table or counter. Check

the level front to back and side to side. Adjust the legs to the

correct level.

IMPORTANT:

THE PERSON INSTALLING THIS APPLIANCE IS RESPONSIBLE

FOR ENSURING THAT ELECTRIC AND WATER CONNECTIONS

MEET THE REQUIREMENTS OF THE NATIONAL ELECTRIC

CODE, NATIONAL PLUMBING CODE, AND ANY LOCAL

ORDINANCES.

Water Hook-up

1) Water inlet (supply) fitting is located at rear of unit.

2) Use 1/4" copper or flexible water line to prevent strain. Do not use low temperature plastic tubing. The connection

is 1/4" flare.

3) Water line pressure must be from 30 to 70 psi.

4) Hot (up to 160F) or cold water may be used. Hot water offers faster recovery between brews, (Use cold water only

if in-line water filters are implemented before the brewer).

5) Install a shut-off valve near the brewer.

6) Installing a filtering system can improve the taste of brewed coffee and extend the life of the brewer. If your water

has high calcium (lime), chlorine, or iron content, this is especially important. The filter should be the lime inhibiting

type if cold water is used. Contact our Customer Service Department to select the filter for your conditions.

Printed in the U.S.A.

1004 FORM # AM-308-06

Part # A090-085

Prior authorization must be obtained from

Grindmaster for all warranty claims.

Table of Contents

Installation and Start-up ......................................1-2

Operation ............................................................3

Adjustments ..........................................................4-5

Cleaning ..........................................................5-6

Service ............................................................7

Troubleshooting

Filling Problems .................................... 8

Heating Problems ................................. 9

Brewing Problems ................................ 10

Exploded View for P200-E ....................................11

Exploded View for P200 (G version)......................12

Exploded View for RAPS200-E..............................13

Exploded View for RAPS200 (G version) ..............14

Rough-In Drawing for P200-E................................15

Rough-In Drawing for RAPS200-E ........................

Wiring Diagram for P200E/RAPS200-E ..........17

Grindmaster Corporation™

4003 Collins Lane

Louisville, KY 40245 USA

(502) 425-4776 (800) 695-4500

(800) 568-5715 (Technical Service Only)

FAX (502) 425-4664

www.grindmaster.com

1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - Airpot/Shuttle Brewer Series

P200E Shuttle & RAPS200E Airpot/Shuttle Brewer SeriesOperation and Instruction ManualInstallationWARNING: ELECTRIC SHOCK HAZARD!INSTALLATION OF T

Page 2

Page 9Troubleshooting: Filling, Heating, and Brewing (con’t.)Tank does notheat.Thermostat faulty or out of calibration.Heater faulty.Make sure thermo

Page 3 - WARNING: HOT LIQUID HAZARD

Page 10Troubleshooting: Filling, Heating, and Brewing (con’t.)Brewing ProblemsThe brewing system consists of the following components:• Start and St

Page 4 - CAUTION: HOT LIQUID HAZARD

Page 11P200/RAPS200 BrewersExploded View for the P200-EITEMDESCRIPTION PART#

Page 5 - Adjustments

Page 12P200/RAPS200 BrewersExploded View for the P200 (G version only)ITEMDESCRIPTION PART #

Page 6 - WARNING: BURN HAZARD

Page 13P200/RAPS200 BrewersExploded View for the RAPS200-EITEMDESCRIPTION PART #

Page 7

Page 14P200/RAPS200 BrewersExploded View for the RAPS200 (G version only)ITEMDESCRIPTION PART #

Page 8

Page 15P200/RAPS200 BrewersRough-In Drawing for the P200-E

Page 9

Page 16P200/RAPS200 BrewersRough-In Drawing for the RAPS200-E

Page 10 - P200/RAPS200 Brewers

Page 17P200/RAPS200 BrewersWiring Diagram for P200-E/RAPS200-E

Page 11

Page 12 - Exploded View for the P200-E

Page 13

WARRANTYfor P200/RAPS200 SeriesGENERAL WARRANTY INFORMATIONGrindmaster maintains the highest standard of quality control in the manufacturing of Ameri

Page 14

Page 2P200/RAPS200 BrewersInstallation (con't.)Electric hook-up1) The electric ratings for your brewer are printed on its nameplate. Typical elec

Page 15

Page 3OperationCAUTION: HOT LIQUID HAZARDWATER USED FOR BREWING COFFEE IS VERY HOT. USE CAUTIONWHEN BREWING, POURING, OR TRANSPORTING COFFEE. ACCID

Page 16

Page 4AdjustmentsWARNING: ELECTRIC SHOCK HAZARDDANGEROUS ELECTRIC VOLTAGES ARE PRESENT NEAR ADJUSTABLECOMPONENTS. ALL ADJUSTMENTS SHOULD BE PERFORME

Page 17

Page 5Thermostat AdjustmentThe thermostat controls the water temperature in the tank. Factory setting is 195 degrees F. Thisis the ideal temperature

Page 18

Page 6Weekly or Bi-Weekly, Depending on Use (P200 Only):1) Fill Shuttle with one gallon of hot water.2) Pour the recommended concentration of urn clea

Page 19

Page 7P200/RAPS200 Brewers To Drain The Water TankCAUTION: HOT LIQUIDS / BURN HAZARDWATER IN TANK IS VERY HOT. USE CAUTION WHEN DRAINING TANK. ACCIDE

Page 20 - WARRANTY

Page 8Troubleshooting: Filling, Heating, and BrewingOverfillingwatertank evenwhen power is off.Fill valve not sealingproperly.Fill valve installedbac

Comments to this Manuals

No comments

Grindmaster P200E User Manual

Browse online or download User Manual for Coffee makers Grindmaster P200E. Grindmaster P200E User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Coffee makers Grindmaster P200E